Materialographic Preparation of Specimens Produced by 3D-Printing Technologies

Materialographic Preparation Process

In the following, we will demonstrate the materialographic preparation process of a sample produced by additive manufacturing. In materialography, a sample taken from a work piece is called specimen.

A typical materialographic examination includes the following steps:

• Sectioning e. g. with an abrasive cutter
• Mounting which offers several advantages for further preparation
• Grinding/polishing for the preparation of the microstructure

Examination by:

• Hardness testing
• Analises de Imagem

Cut-Off-Machine setup. Detail: clamped sample (clamping tool: vertical vice single)

For this article a steel sample (X6Cr17, material number: 1.4016) manufactured by additive laser powder build-up welding was investigated. The first step was to obtain a smaller sample piece (=specimen) which is representative of the complete workpiece. This was achieved by using QATM’s precision cutter with a thin CBN (cubic boron nitride) blade (wheel thickness: 0.65 mm, wheel diameter: 153 mm).

The cutting was effected with a pulsed direct cut (0.2 mm forwards and 0.2 mm backwards) with a feed speed of 1 mm/s and a rotational speed of 4500 rpm.

After cutting, the specimen was mounted in a hot mounting material (Epo black) with a hot mounting press to obtain a specimen which is easier to handle. Mounting was carried out at a pressure of 200 bar for 6 minutes at 180°C, followed by a cooling cycle of 6 minutes. Another advantage is the high degree of parallelism of the mounted specimens of 51 µm ±1 µm (the tolerances are based on the caliper used for height measurements of the specimens). The mounted specimens were ground (individual force) and polished (individual force) afterwards with a semiautomated grinding and polishing machine.

The grinding process was divided into two steps. The first one was plane grinding using a silicon carbide (SiC) grinding paper with grit size P240 to remove all deformations caused by the cutting process. This was followed by grinding with a SiC paper with grit size P600 to smoothen the surface for subsequent polishing steps. First, the specimen was prepolished with the hard Galaxy BETA polishing cloth and 9 µm polycrystalline diamond suspension, followed by a medium-hard cloth made of silk and 3 µm poly diamond suspension. The last step, called final polishing, was done on a soft synthetic polishing cloth and Eposil M.

The detailed preparation parameters are indicated in this table:

Based on this preparation sequence, a finely polished specimen surface was obtained. Figure 1 shows an image taken with an incident optical microscope (incident light) at a magnification of 100.

As the light is reflected almost equally over the whole specimen surface, the microstructure remains invisible. Due to the nature of the human eye, a minimum difference in contrast of 10% is needed to make the contrast visible on any surface. This contrasting is achieved by etching. In our example, the etchant “V2A Beize” for pickling was used to contrast the surface by selective etching of the different phases of the investigated X6Cr17 steel. Etching was done for 45 s and the microstructure is very well discernible as can be seen in the picture.

The microstructure was also contrasted well in the middle of the specimen surface indicating that the whole prepared surface was successfully contrasted as shown in the picture. Figura 2

Exames adicionais, como o teste de dureza, exigem uma superfície plana e lisa para fornecer resultados confiáveis e significativos. O processo de preparação materialográfica descrito acima garante que a amostra esteja idealmente adequada para o teste de dureza. A QATM oferece o Qness 60 A+ para este propósito, um instrumento poderoso para teste de microdureza e avaliação óptica. A superfície polida na Fig. 1 mostra várias trincas. A borda reta à esquerda foi alcançada por fresamento. O contorno das costuras de solda (welded seams) não está visível. Para um exame mais detalhado, o contraste foi aprimorado por ataque químico (etching). A superfície atacada quimicamente é mostrada na Fig. 2. Ela apresenta mais trincas e os pontos coloridos indicam áreas com excesso de ataque químico próximas a várias trincas devido a resíduos do agente de ataque. As costuras de solda, que possuem dimensões diferentes, estão bem visíveis. A técnica de deposição camada por camada efetua o tratamento térmico da camada subjacente. Uma zona afetada pelo calor (ZAC) é formada e causa uma mudança na microestrutura, afetando as propriedades da amostra. Por exemplo, a dureza pode ser reduzida, resultando em estresse mecânico. Como camadas de durezas diferentes são depositadas uma sobre a outra, o estresse mecânico aumenta continuamente e pode levar às chamadas trincas secundárias. Uma razão para a formação de trincas primárias são os gradientes de resfriamento durante a deposição. A Fig. 3 mostra uma ampliação dos cordões de solda individuais e suas correspondentes zonas afetadas pelo calor. O teste de dureza pode revelar as diferenças na dureza das camadas depositadas.

Figura 1: Image of the prepared specimen surface. Due to the polished surface the light is reflected almost equally and the microstructure is not discernible.

Figura 2: Etched specimen using "V2A Beize" (for 45 s). Edge section. The microstructure is clearly discernible.

Figura 3: Contrasted specimen. The welded-based microstructure of the manufactured workpiece is clearly visible.