Applications for Battery Technology
The energy transition requires effective concepts for energy storage, as renewable energy sources such as solar and wind are not continuously available. Therefore, a reliable energy supply is not possible without suitable storage solutions. Lithium-ion batteries have established themselves as the best available battery solution due to their high energy density, long lifespan, low self-discharge, and fast charging capability.
Tailored metallographic preparation is essential for better understanding and further developing the materials and structures of these batteries. It provides detailed insights into the microstructure, material composition, and quality of the individual components and joints, contributing to the optimization of lithium-ion batteries.
Métallographie / Matérialographie Exemples d´applications
Investigation of lithium metal oxide particles
Lithium metal oxide particles are subjected to metallographic preparation and examined by light microscopy and scanning electron microscopy with EDX detector to investigate their size and chemical composition.
QATM‘s epoxy-based cold mounting materials (Qpox 90 and Qpox 92) allow for mounting the oxide particle powders without any gaps, preparing them for grinding and polishing. Thanks to an extensive selection of polishing cloths and polishing diamond suspensions, a wide variety of lithium metal oxide particles can be prepared. The Qdoser system is used for automated dosing during polishing and fine polishing.
Short facts
- Metallographic preparation for optical microscopy investigation
- Metallographic preparation for optical microscopy investigation
Field of use
- Research & Quality Control
An example of powder particles mounted in Qpox 90.
Unité de dosage Qdoser ECO & Consommables
Cutting of lithium-ion batteries
LIB cutting can vary depending on the desired outcome. Cut-off machines can be used for sectioning the battery casing to take the whole jelly roll out, or for cutting the whole battery with casing and electrodes, while a scalpel is suitable for sectioning only the electrode foils.
A rotating clamping tool is used to cut the casing and take the jelly roll out. QATM cut-off machines offer a wide range of clamping tools for sectioning entire batteries. The image below demonstrates an LIB cutting process.
Short facts
- Saving time by cutting the sample near to the target surface.
- Use of rotation device to clamp the samples.
Field of use
- Research & Quality Control
Sectioning of a complete LIB with QATM cut-off machine
Machine de tronçonnage Qcut 350 A
Mounting of lithium-ion batteries
Mounting Lithium-Ion batteries involves different techniques depending on the components being handled. The casing and spot weld can be hot mounted in some cases, but the electrodes require cold mounting due to their sensitivity to temperature and pressure. Mounting can be performed before cutting to ensure foils and other components remain in the sample. It can also be done after cutting to prepare the sample for grinding and polishing. To prevent gaps between the mounting materials and the sample during cold mounting, it is recommended to use mounting materials with minimal volume shrinkage and polymerization temperature. For mounting LIBs, the epoxy-based cold mounting materials QATM Qpox 90 and Qpox 92 are the best choices due to their low polymerization temperature of 60°C and 35°C, respectively, and minimal gap formation.
Short facts
- Using epoxy-base cold mounting materials with minimum polymerization temperature and shrinkage.
- High flexibility by hot mounting due to preheating function, cooling modes, maintenance tasks and user account management feature.
Field of use
- Research & Quality Control
Cold mounted LIB samples
Enrobage à chaud Qpress 50
Grinding and polishing of lithium-ion batteries
Grinding and polishing can be done on different parts of LIBs. Sometimes the casing should be prepared and examined under light microscopy or SEM (also with EBSD detector), in other cases the electrodes or spot welds should be prepared. The cap of the LIB is in many cases low carbon steel with Ni-coating. The image shows the cap of an LIB after 1 μm polishing and etching with Klemm I. For powering certain devices, large battery packs consisting of multiple lithium-ion cells connected in parallel-series configurations are required. A robust and flawless spot weld is a critical concern for many industries, like aerospace. The other important parts of LIB are electrodes. The anode is often a copper foil coated on one or both sides with graphite, and the cathode is in many cases an aluminum foil coated on one or both sides with metal oxide particles (for example LiNiMnCoO2 particles).
Short facts
- Water-free polishing suspensions and lubricants
- Water-free polishing suspensions and lubricants
Field of use
- Research, Quality Control & Production
Machine à meuler et à polir Qpol 250 A2-ECO
Machine à meuler et à polir Qpol 250 A2-ECO
Vous souhaitez obtenir plus d'informations ?
Si vous avez d'autres questions, n'hésitez pas à nous contacter via notre formulaire de contact. Nous sommes toujours heureux de vous aider à trouver la bonne solution pour vos applications de tests de matériaux.
Contactez-nous dès aujourd'hui
Si vous souhaitez en savoir plus sur la préparation matérialographique d'échantillons pour la géologie et la minéralogie, ou si vous êtes intéressé par nos produits, n'hésitez pas à nous contacter. Nous nous ferons un plaisir de vous conseiller et de vous faire une offre personnalisée en fonction de vos besoins et de votre budget. Vous pouvez nous contacter par téléphone, par e-mail ou via notre site web. Nous nous ferons un plaisir de répondre à votre demande.
